Wireless Lighting & Control System

The Wireless Lighting & Control System provides everything you’ve come to expect from Colorado vNet – reliability, stylish design, and simple yet powerful programming.

Retrofit Solution

Perfect for both retrofit and new construction projects, our Wireless Lighting & Control System uses standard household wiring and state-of-the-art radio frequency (RF) controlled devices for whole–house or single–room scenes.

There’s no need to pull new wires. Simply replace existing switches with one-, two-, three- or four-button Touchpad Dimmers. For instance, swap out the one on/off master bedroom switch with a four-button Touchpad Dimmer to take advantage of WAKE, SHADES, READING and NIGHTLIGHT scenes.


Robust Communication

Designed for ZigBee®, the wireless system utilizes mesh networking to provide unprecedented range and reliability without special repeaters. Spread spectrum technology and encrypted data transmissions make the system highly secure—so it’s perfect for large estates or multiple dwelling units (MDUs).

A typical wireless system can support up to one hundred wireless devices. Plus, you can easily connect to our wired Lighting & Control System or our Vibe Audio System.


Complete Control

Simple and intuitive, our award-winning Touchpad Dimmer offers full scene control at every touchpoint—no separate dimmers and keypads are required, eliminating wall clutter.

But, more than just Touchpad Dimmers, the full line of Colorado vNet wireless products comprise a complete control system. Control lamps and other plug-in devices, shades, fireplaces, gates, etc. The system can also activate scenes based on inputs from PIRs and other sensors, RS-232 or IR controllers, and even time-of-day or sunrise/sunset.


Wireless Lighting and Control System Diagram - Rollover for more information
Complete Control


Next: The Wireless Touchpad Dimmer
Wireless Touchpad 1 Wireless Touchpad 2 Wireless Touchpad 3 Wireless Touchpad 4 RS-232/IR Module Input/Output Module Wireless Wall Plug Dimmer Wireless Wall Plug Switch Wireless MultiLink Module

 

Elegantly simple and intuitive, our award-winning Touchpad Dimmer represents a union of quality appearance, ergonomic design and superior system architecture. This three-in-one device (touchpad, 750 Watt dimmer and wireless repeater) is the basic building block of our Wireless Lighting & Control System. Touchpad Dimmers work with or without a neutral wire.

 

Elegantly simple and intuitive, our award-winning Touchpad Dimmer represents a union of quality appearance, ergonomic design and superior system architecture. This three-in-one device (touchpad, 750 Watt dimmer and wireless repeater) is the basic building block of our Wireless Lighting & Control System. Touchpad Dimmers work with or without a neutral wire.

 

Elegantly simple and intuitive, our award-winning Touchpad Dimmer represents a union of quality appearance, ergonomic design and superior system architecture. This three-in-one device (touchpad, 750 Watt dimmer and wireless repeater) is the basic building block of our Wireless Lighting & Control System. Touchpad Dimmers work with or without a neutral wire.

 

Elegantly simple and intuitive, our award-winning Touchpad Dimmer represents a union of quality appearance, ergonomic design and superior system architecture. This three-in-one device (touchpad, 750 Watt dimmer and wireless repeater) is the basic building block of our Wireless Lighting & Control System. Touchpad Dimmers work with or without a neutral wire.

 

 

The RS-232/IR Module contains one RS-232 port and one IR input and simplifies system integration by controlling third party devices or vice versa.

 

 

With the Input/Output Module, the wireless system triggers lighting scenes based upon one sensor input and can trigger one low voltage relay output.

 

 

The Wall Plug Dimmer integrates floor/table lamps and other dimmable plug-in devices up to 400 Watts into your lighting scene.

 

 

The Wall Plug Switch serves as a 15 Amp relay for on/off control of high-wattage plug-in devices.

 

 

The MultiLink Module provides the connection between the three primary Colorado vNet networks — CAN for wired lighting, ZigBee for wireless lighting, and Ethernet for audio, climate and security. Required for commissioning any wireless system, the MultiLink Module only needs to remain if the system consists of more than one network type.

© Copyright 2014 3vNet Inc. All Rights Reserved.
Home  |  Contact Us  |  Privacy Policy  |  Trademarks